[W5SFA] QRP Labs U3S kit report

[Gilbert Franke]

Thanks, Roger!  Did you build yours with three transistors right away, or
just one to begin with?  I'll check out that antenna site.  Thanks.  Yes,
that is what the manual seemed to indicate could  happen if only one string
was received -- or both received, but not connected at the receiving end.

Dan, I know you will enjoy it when you get it done.

-- Gil

On Mon, Jun 26, 2017 at 3:03 PM, Roger Klein <rwklein at katyweb.net> wrote:

> I thought I'd share my U3S experience, after taking it along on a recent
> trip down to Rockport.  I used a Par End Fedz 10-20-40
> <https://www.lnrprecision.com/store/#!/EFT-10-20-40-Trail-Friendly/p/39885475>
> lightweight antenna, and had it strung haphazardly up in some trees about
> 15' high.  I transmitted for 4 days on 20m and 40m without a hitch, and was
> being heard - maybe not as good as the better antennas back home but
> getting lots of reports.
>
>
>
> When I started up at the new location, my grid square was automatically
> updated by the GPS to be in grid EL17.  The wsprnet.org map shows the
> location as the center of the grid square, which in this case was out in
> the Gulf of Mexico!  I then changed to sending two successive frames, so I
> could send my 6 character grid square.  As expected, I got a much more
> accurate map posting (EL17kx).  Not every spot showed the 6 character grid
> square though - only those stations that received both frames.  The
> stations that received only one of the frames only posted the 4 character
> grid square.
>
>
>
> I think for a multiband antenna, the myantennas.com EFHW-8010 or
> EFHW-4010 could work well.  See http://myantennas.com/wp/
> product-category/antennas/efhw-multi-band/
>
>
>
> You could also scratch build one of these types of antennas using a 9:1
> balun.  But even with a poorly tuned antenna, I think we'd get some spots,
> and with the low power I doubt there would be any danger of blowing the
> transistor because of high SWR.
>
>
>
> 73,
>
>
>
> Roger N5RWK
>
>
>
>
>
> *From:* w5sfa [mailto:w5sfa-bounces at w5sfa.org] *On Behalf Of *Gilbert
> Franke
> *Sent:* Monday, June 26, 2017 1:35 PM
> *To:* SFAustin Radio Club
> *Subject:* [W5SFA] QRP Labs U3S kit report
>
>
>
> I'm having a good time with my QRP Labs Ultimate3S QRSS/WSPR Transmitter.
> The GPS receiver works very well to give my location and frequency
> calibration.  I am heard on the WSPR network and posted on their map with
> almost every beacon, at 10 minute intervals.  I haven't seen any reports
> outside Canada and USA, but that is with a nominal 200 mW on 30M with an
> end fed halfwave antenna about 20 feet, north / south, and SWR of 1.3:1.
>
> You can see me on the WSPRnet.org map. Select 30M filter from lower left
> corner.  Because of the slow speed (it takes about 110 seconds to transmit
> my callsign, 4 character Maidenhead locator, and power!), sending the 6
> character Maidenhead locator is not encouraged.  The four character locator
> put me between Halletsville and Shiner.  (If it had taken me all the way to
> Shiner, I would have been happy!)  When I re-configured for the full 6
> character locator, I show up about 1 mile outside of Bellville!  As the
> manual says, this is a limitation in the WSPR protocol, not the U3S. Does
> anyone know what mode the APRS system runs? Do you think the U3S could
> handle that?
>
>
>
> I have low  pass filters for 40, 30, and 20 M, but I don't have a well
> tuned antenna for 40 or 20.  I guess that is the next project!
>
>
> --
>
> ​73, de Gil WB5RFQ​
>
>
>
> ----
>
> Gilbert A Franke <http://www.gilbertfranke.com>
> (361 442 6008 <(361)%20442-6008> - cell)
> 130 N Harris Street
> Bellville TX  77418
>
>
>
> _______________________________________________
> w5sfa mailing list
> w5sfa at w5sfa.org
> http://mail.w5sfa.org/mailman/listinfo/w5sfa_w5sfa.org
>
>


-- 

----
Gilbert A Franke <http://www.gilbertfranke.com>
(361 442 6008 - cell)
130 N Harris Street
Bellville TX  77418
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mail.w5sfa.org/pipermail/w5sfa_w5sfa.org/attachments/20170626/c278e338/attachment.htm>